It allows you to create a bootable USB to boot into Clover.Here are the steps I had to take on my MacBook, originally procedure was written in macOS High Sierra, but I tested it in MacOS Mojave 10.14.2 as well. Clover EFI Bootloader does exactly this, allowing macOS, Windows, and Linux systems to run. However, the latest Windows 10 ISO is too large to sit on a FAT32 partition so you have to split the install.wim into small. So the only working file system for Mac is FAT32 if you want to create a Windows bootable USB on Mac. This approach will be simpler for any other ISO image like Ubuntu or CentOS, so there’s a separate Steps 3-5 for them at the end of the post.macOS does not support NTFS by default and exFAT is not recognized as a bootable device by most computer motherboards.copy all the files from that folder onto the USB stick format USB stick with FAT-32 filesystem erase USB stick and create MBR (master boot record) So the first two steps are the same, then Windows and Linux have separate procedure. For generic Linux installation ISOs this procedure would be simpler. Windows 10 bootable USB vs Linux ISO USBWindows 10 is a very specific bootable media, so the process is a bit involved.
![]() Create Bootable Usb From Windows Mac Is FAT32![]() /Volumes/WIN10/If you remember, in Step 3 we did the df command and the USB filesystem /Volumes/WIN10 was empty.Just to get an idea that the copy was successful, let’s run the df command again to make sure the USB stick has roughly the same amount taken up now – 4.1GB as per output fragments in previous step. That’s exactly where you are if you just completed Step 4.The copy will take good 10-15min: $ sudo cp -r. /Win10_1607_English_x64.isoYou’ll have the MacOS Finder window with Windows ISO content pop-up, just ignore it and go back to the terminal.You should now have it mounted under folder like this: :/Volumes/SSD $ df -h | grep EN-US/dev/disk8 4.1Gi 4.1Gi 0Bi 100% 18446744073707414141 2138557 1704874683337099264% /Volumes/CCSA_X64FRE_EN-US_DV5Go into that folder and do ls to make sure you can see Windows DVD files there: :/Volumes/SSD $ cd /Volumes/CCSA_X64FRE_EN-US_DV5/:/Volumes/CCSA_X64FRE_EN-US_DV5 $ lsAutorun.inf boot bootmgr bootmgr.efi efi setup.exe sources supportExcellent! Step 5: Copy Windows files onto USB stickRight, now we have to copy all the files from DVD ISO image onto our new USB stick.IMPORANT: you should be in the /Volumes/CCSA_X64FRE_EN-US_DV5 directory when running this command below. Forward emails to another email address in outlook for mac/CentOS-7-x86_6.isoCreated: /Volume/Stuff/dist/centos.dmg Step 4: write DMG image onto USB stick with ddExellent, now we are ready to burn the ISO image. $ hdiutil convert -format UDRW -o centos. It’s /dev/disk9 in our case: :/ $ diskutil unmountDisk /dev/disk9Unmount of all volumes on disk9 was successful Step 3: convert ISO into bootable DMGWARNING: this is an important step, without it your USB stick won’t boot.So I have this DVD ISO of the CentOS 7.4, let’s convert it before burning onto the USB stick. The rule of thumb is to boot UEFI if it’s available, especially if you’re booting Windows USB stick:As I said earlier, non-Windows ISOs are much easier to deal with! So after the first 2 generic steps at the start of this post, we’ll be taking separate steps for Linux as shown below.We need to unmount the USB disk we found in Step 2. Step 6: Boot USB stick on your PCIMPORTANT: recent enough PCs will likely offer you both legacy boot and UEFI boot.
0 Comments
Leave a Reply. |
AuthorGary ArchivesCategories |